Homeowner guide
Polybutylene Pipes: What They Are, How to Spot Them and Why Homes Replace Them
Short answer
Polybutylene (PB) is a gray, blue or black plastic water pipe installed in many US homes from roughly 1978 to 1995. It became known for sudden leaks at the pipe and fittings and led to large class-action settlements. Many insurers and buyers now treat it as a reason to repipe, usually with PEX or copper.
If your home was built or replumbed in that period, it is worth checking which pipe you have.
What is polybutylene pipe?
Polybutylene is a flexible plastic resin that was widely used for water supply piping because it was inexpensive and easy to install. It was popular in new construction, mobile homes and repiping jobs from the late 1970s until the mid-1990s, especially in the South and West where homes were being built quickly.
Polybutylene was used for supply lines inside the house and sometimes for the main service line from the meter. It was not used for drains.
Why does polybutylene pipe fail?
The commonly cited explanation is that chlorine and other oxidants in treated public water react with polybutylene and its acetal plastic fittings, making them brittle and causing small cracks over time. Poor installation, such as crimp rings that were too tight or too loose, added to the problem. Failures often happen without warning, from the inside out, so a pipe can look fine and still be weak.
Widespread failures led to class-action lawsuits, including the well-known Cox v. Shell Oil settlement in the 1990s, which created a claims program for affected homeowners. That claims program has since closed. Polybutylene was later removed from US model plumbing codes and is no longer installed for water supply in homes.
How can I tell if I have polybutylene pipes?
Look at exposed pipe in these places:
- Where the water line enters the house, often near the main shutoff valve
- At the water heater connections
- Under sinks and behind toilets, where pipes come out of the wall
- In the basement, crawl space or attic
- At the water meter, where the service line connects
Identifying features:
| Feature | Polybutylene | PEX (modern) | CPVC |
|---|---|---|---|
| Color | Usually gray inside; sometimes blue or black outdoors | Red, blue, white or clear-ish | Cream or tan |
| Feel | Flexible | Flexible | Rigid |
| Markings | Often stamped with the code PB2110 | Marked PEX with a standard such as ASTM F876 | Marked CPVC |
| Fittings | Gray or white plastic, or copper or aluminum crimp rings | Brass or plastic fittings with crimp, clamp or expansion rings | Glued fittings |
Note that pipe stubs coming out of walls may be copper even when polybutylene runs inside the walls. Checking the attic, crawl space or basement gives a better picture. A plumber or home inspector can confirm the material.
Do I have to replace polybutylene pipes?
No law requires homeowners to remove existing polybutylene, but there are good reasons many do:
- Risk of sudden leaks, which can cause major water damage, especially in an attic or upper floor.
- Insurance: some insurers will not write a new policy, may charge more or may limit water damage coverage on homes with polybutylene.
- Home sales: inspectors flag it, buyers may ask for credits, and lenders or insurers may raise questions.
- No fix for the material: replacing fittings does not change the pipe itself.
What is polybutylene usually replaced with?
| Material | Pros | Considerations |
|---|---|---|
| PEX | Flexible, fewer fittings, quick to install, resists freeze splitting better than rigid pipe | Must be protected from sunlight; follow maker's chlorine rating |
| Copper | Long track record, rigid, recyclable | Can corrode with aggressive water; more fittings and labor |
| CPVC | Rigid plastic, glued joints | Can become brittle with age and cold; less common for repipes today |
A whole-house repipe typically replaces all supply lines, with new shutoff valves at fixtures. If the service line from the meter is also polybutylene, consider replacing it at the same time. See repiping and main water line replacement.
What happens during a polybutylene repipe?
- The plumber inspects the home and plans pipe routes through attics, walls and crawl spaces.
- A permit is pulled where required.
- Small openings are made in drywall to run new lines; new pipes are connected to each fixture and the water heater.
- The system is pressure tested and inspected.
- Old polybutylene is disconnected or removed where accessible.
- Drywall openings are patched, by the plumber or a separate contractor.
Most homes keep water service for much of the job, with outages during tie-ins.
What should I do until the pipes are replaced?
- Know where the main shutoff is. See finding your main shutoff.
- Consider a pressure reducing valve if water pressure is high, since high pressure stresses fittings.
- Check exposed fittings for white flaking or drips.
- Consider water leak sensors or an automatic shutoff valve.
- Shut off the water when away for extended periods.
Is polybutylene common in mobile and manufactured homes?
Yes. Polybutylene was widely used in manufactured and mobile homes built during its peak years, because it was light and quick to install. In these homes the pipe often runs under the floor, inside the belly wrap, where leaks can go unnoticed. Owners of manufactured homes from that era should check under sinks, at the water heater and where the supply line enters under the home.
Was polybutylene used for the main water line?
Often, yes. Blue or black polybutylene was used for underground service lines from the meter to the house. A leak in a buried service line can show up as a rising water bill, a wet area in the yard or low pressure. Look where the line comes up from the ground near the house or inside the meter box. If the service line is polybutylene, many homeowners replace it at the same time as the interior pipes. See water line repairs.
Polybutylene when buying or selling a home
- Buyers: ask the home inspector to identify pipe material, and check with insurers before closing. Some buyers negotiate a repipe credit.
- Sellers: many states require disclosure of known defects. Having a repipe done, with a permit and final inspection, can remove a common objection.
- Records: keep the permit, invoice and photos showing the pipe was replaced. Insurers and future buyers may ask for proof.
What does a polybutylene failure look like?
Failures tend to happen in a few typical ways. Fittings crack, especially the gray or white plastic acetal fittings, and start spraying or dripping. Crimp rings that were installed too tight or too loose let a joint pull apart. The pipe itself can develop small splits or flaking on the inside that eventually leak. Signs to watch for include white or gray flaking around fittings, small drips at joints, water stains on ceilings below attic lines and unexplained water bill increases. Because failures can come without warning, many owners do not wait for the first leak before replacing it.
Frequently asked questions
What years was polybutylene pipe installed?
Roughly 1978 to 1995 in the United States, with some installations outside those years.
Is polybutylene pipe safe for drinking water?
The main concern with polybutylene is leaks and failure, not drinking water safety. If you have questions about your water quality, have it tested.
Can I get insurance on a house with polybutylene?
Some insurers will, sometimes with limits or higher rates, and some will not. Ask several insurers and get answers in writing.
Is gray plastic pipe always polybutylene?
Not always. Some PEX is gray. Check for the PB2110 marking or have a plumber confirm.
Can I replace polybutylene a little at a time?
Some homeowners replace the most vulnerable sections first, such as lines in the attic or near the water heater. A full repipe is usually more efficient and removes the risk in one project.
Related services
Need a plumber?
Drains, leaks, water heaters, sewer lines and emergencies, day or night.
Call (855) 902-0055