Plumbing services
Water Heater Installation & Replacement
Replacing a water heater means choosing the right type and size, then installing it to code: correct gas venting or electrical supply, a working T&P relief valve and discharge pipe, an expansion tank where the system is closed, seismic straps where required, and a permit and inspection in most areas. The old unit is drained, removed and hauled away.
Most homeowners replace a water heater when the old one leaks or stops working, so the decision often has to be made quickly. Knowing your options ahead of time, including tank size, fuel type and whether a heat pump or tankless model fits, helps you make a good choice under pressure.
Signs you need water heater installation & replacement
- The tank is leaking from the bottom or the jacket
- The water heater is near or past its expected life
- Rusty water from the hot side only
- Not enough hot water for your household
- Repeated repairs on an older unit
- Rising energy bills with no change in use
- Remodeling or adding a bathroom
- Switching fuel or upgrading to a heat pump or tankless unit
What Size Water Heater Do I Need?
Tank heaters are labeled by gallon capacity, but the more useful number is the first-hour rating (FHR), found on the yellow EnergyGuide label. It tells you how much hot water the heater can deliver in one busy hour. The U.S. Department of Energy recommends matching FHR to your household's peak-hour demand.
As a rough starting point, many plumbers use these ranges:
| Household | Common tank size (gas) | Common tank size (electric) |
|---|---|---|
| 1 to 2 people | 30 to 40 gallons | 40 gallons |
| 2 to 4 people | 40 to 50 gallons | 50 gallons |
| 3 to 5 people | 50 gallons | 50 to 66 gallons |
| 5 or more people | 50 to 75 gallons | 66 to 80 gallons |
Electric tanks recover more slowly than gas, which is why they are often sized larger. Large soaking tubs, multiple showers at once and teenagers all push demand up. Your plumber should ask about how you use hot water, not just copy the old tank size.
Gas vs Electric vs Heat Pump vs Tankless
| Type | How it heats | Good fit when | Installation notes |
|---|---|---|---|
| Gas tank | Burner under the tank | Home has natural gas or propane; you want fast recovery | Needs proper venting, combustion air and a gas connection |
| Electric tank | Two electric elements | No gas available; simple installation | Needs a dedicated 240-volt circuit; slower recovery |
| Heat pump (hybrid) electric | Moves heat from surrounding air into the water | You want lower electric use; there is space and air volume around the unit | Needs room air volume or ducting per the manufacturer, a condensate drain and usually 240 volts; cools the space around it |
| Tankless | Heats water on demand | Space is tight; you want continuous hot water | Often needs a larger gas line or big electric service and new venting |
Federal efficiency standards that took effect in 2015 effectively require larger electric tanks, over 55 gallons, to use heat pump technology, and larger gas tanks to use condensing technology. For a closer look, read tankless vs tank water heaters or visit our tankless water heater page.
Venting for Gas Water Heaters
Gas water heaters must vent their exhaust safely outdoors. The main types are:
- Atmospheric vent: exhaust rises through a metal vent into a chimney or B-vent. Simple, but sensitive to drafting problems.
- Power vent: a fan pushes exhaust out, often through a sidewall with plastic pipe. Needs an electrical outlet.
- Direct vent: draws combustion air from outside and vents outside through a sealed system.
A new heater may not fit the old vent. A larger heater, a change in vent type or a furnace upgrade that leaves the water heater alone in an oversized chimney can all require vent changes. Poor venting can cause backdrafting of carbon monoxide, so working CO alarms are important.
Code Items Every Installation Should Include
- Permit and inspection. Most jurisdictions require a permit to replace a water heater, even like for like.
- T&P relief valve and discharge pipe run full size to an approved location, without valves or caps.
- Expansion tank where the plumbing is a closed system, such as homes with a check valve, backflow preventer or pressure reducing valve.
- Seismic strapping. California law requires water heaters to be braced, anchored or strapped to resist falling or moving during an earthquake, and other areas have similar rules. Straps are usually placed in the upper and lower portions of the tank.
- Drain pan with a drain line where a leak could damage the building, such as in attics or upper floors.
- Elevation of gas units in garages where code requires the ignition source to be raised off the floor, unless the heater is listed as flammable vapor ignition resistant and local code allows it.
- Gas shutoff and sediment trap, or a correct electrical disconnect and wiring.
- Proper clearances from combustibles and room for service.
What Happens on Installation Day
- Shut off water, gas or power to the old heater
- Drain and disconnect the old unit
- Set the new heater, with a pan and stand if required
- Connect water lines, often with new valves and connectors
- Connect gas and venting, or electrical wiring
- Install the T&P discharge pipe, expansion tank and straps
- Fill the tank completely before turning on gas or power, which protects electric elements from burning out
- Light or power up, check for leaks and set the temperature
- Haul away the old heater for disposal or recycling
The U.S. Department of Energy suggests 120°F as a setting that saves energy and lowers scald risk for most households.
What Affects the Cost of Water Heater Installation
- Type, fuel and capacity of the new heater
- Changes to venting, gas line or electrical circuit
- Switching types, such as tank to tankless or gas to heat pump
- Location and access: basement, garage, attic, closet or crawlspace
- Code upgrades: expansion tank, straps, pan, stand, discharge piping
- Permit fees and local inspection requirements
- Removal and disposal of the old unit
- Emergency or same-day service
Some utilities and governments offer rebates or tax incentives for high-efficiency models, especially heat pump water heaters. Check with your utility before you buy.
How it works
- Call (855) 902-0055Tell us what is going on and your address. We answer 24/7.
- A local plumber comes outA plumber serving your area arrives, finds the problem and explains it.
- Fixed rightYou get the price before work starts, then the job is done and cleaned up.
Water Heater Installation & Replacement: common questions
How long does it take to install a water heater?
A straightforward like-for-like tank replacement often takes a few hours. Switching to a tankless or heat pump unit, or moving the heater, can take a day or more, especially if gas, venting or electrical changes are needed.
Do I need a permit to replace a water heater?
In most areas, yes. Permits help ensure the venting, gas connection, relief valve and other safety items meet code. Your plumber can usually pull it.
Do I need an expansion tank on a new water heater?
You typically do if your plumbing is a closed system, such as when there is a check valve, backflow preventer or pressure reducing valve on the main line. Local codes and the water heater manufacturer may also require one.
Is a heat pump water heater worth it?
Heat pump water heaters use much less electricity than standard electric tanks. They need enough surrounding air space, a condensate drain and usually a 240-volt circuit, and they cool the room they are in. They suit many basements, garages and utility rooms.
Do water heaters need to be strapped?
California requires water heaters to be braced or strapped against earthquakes, and some other areas have similar rules. Strapping is a good idea in any seismic area.
How long do water heaters last?
Tank water heaters commonly last around 8 to 12 years, depending on water quality, maintenance and the model. Tankless units often last longer. See our water heater lifespan guide.
Should I replace my water heater before it fails?
If your tank is near the end of its expected life, planning a replacement lets you compare options and avoid a sudden leak. Signs like rusty hot water, rumbling and moisture at the base suggest it is close.
Related
Water Heater Installation & Replacement near you
- Plumber in New York, NY
- Plumber in Los Angeles, CA
- Plumber in Chicago, IL
- Plumber in Brooklyn, NY
- Plumber in Houston, TX
- Plumber in Phoenix, AZ
- Plumber in Philadelphia, PA
- Plumber in San Antonio, TX
- Plumber in Bronx, NY
- Plumber in San Diego, CA
- Plumber in Dallas, TX
- Plumber in San Jose, CA
- Plumber in Austin, TX
- Plumber in Jacksonville, FL
- Plumber in Fort Worth, TX
- Plumber in Columbus, OH
- Plumber in Saint Louis, MO
- Plumber in Charlotte, NC
- Plumber in Indianapolis, IN
- Plumber in San Francisco, CA
- Plumber in Saint Paul, MN
- Plumber in Seattle, WA
- Plumber in Denver, CO
- Plumber in Oklahoma City, OK
Need a plumber?
Drains, leaks, water heaters, sewer lines and emergencies, day or night.
Call (855) 902-0055