Plumbing services
Sump Pump Installation & Repair
A sump pump sits in a pit (sump basin) at the lowest point of a basement or crawl space and pumps out groundwater that collects there, sending it outside through a discharge pipe. Sump pump installation and repair includes replacing failed pumps, fixing stuck float switches, adding battery backup pumps and correcting check valve and discharge line problems.
A sump pump usually works hardest during heavy rain and snowmelt, which is exactly when a failure causes the most damage. Testing it before the wet season and having a backup plan are the best protection for a finished basement.
Signs you need sump pump installation & repair
- Pump runs constantly, even in dry weather
- Pump turns on and off rapidly (short cycling)
- Pump hums but does not move water
- Loud grinding, rattling or banging noises
- Water in the basement or rising in the pit
- The float switch sticks or gets caught on the pit wall
- Visible rust or a pump that is many years old
- No backup pump and frequent power outages in storms
How a Sump Pump System Works
Perimeter drain tile around the foundation and gravel below the slab carry groundwater to the sump pit. As water rises, a float switch turns the pump on. The pump pushes water up the discharge pipe, through a check valve that keeps it from flowing back into the pit, and out of the house to a spot where it drains away from the foundation. When the water level drops, the float turns the pump off.
Every part matters: a stuck float, a failed check valve or a frozen or clogged discharge line can flood a basement even when the pump motor is fine.
Pedestal vs. Submersible Sump Pumps
| Pedestal | Submersible | |
|---|---|---|
| Design | Motor sits on a column above the pit; only the pump base is in the water | Entire sealed pump sits inside the pit, underwater |
| Noise | Louder | Quieter, especially with a pit lid |
| Pit size | Works in narrow or shallow pits | Needs a pit wide enough for the pump and float |
| Service | Motor is easy to reach | Must be pulled from the pit |
| Typical use | Smaller water volumes, tight pits | Most finished basements and higher water volumes |
Pump horsepower and capacity should match how much water enters the pit and how high and far the water must be pushed (the head). A plumber sizes the pump to the home, not just to what was there before.
Battery Backup and Water-Powered Backup Pumps
The primary pump stops if the power goes out, which often happens during the same storms that bring the most water. Backup options include:
- Battery backup pump. A second pump in the same pit runs off a deep-cycle or sealed battery when power fails or the primary pump cannot keep up. Many have an alarm. Batteries need periodic checking and replacement.
- Water-powered backup pump. Uses municipal water pressure to pump water out, with no battery needed. It requires adequate city water pressure and may need a backflow preventer under local code. It is generally not suitable for homes on wells.
- Combination systems that package a primary and backup pump together.
- Generator. A properly installed generator can keep the primary pump running.
A high-water alarm is a simple addition that sounds when water in the pit rises above the normal pump-on level, warning you before water reaches the floor, even if the pump has failed silently.
Check Valves and Discharge Lines
Check valve. Without one, water in the discharge pipe falls back into the pit each time the pump stops, making the pump cycle more often and wear out sooner. A failed check valve often makes a loud thud when the pump shuts off. Many plumbers drill a small weep hole between the pump and check valve to prevent air lock.
Discharge line. The pipe should carry water far enough away that it does not soak back toward the foundation. In cold climates, discharge lines can be blocked by ice, so plumbers may add a protective fitting that lets water escape if the line outside is blocked.
Local rules. Many municipalities prohibit connecting a sump pump to the sanitary sewer, because groundwater can overload sewage systems. Check local code on where discharge may go, including toward neighbors or sidewalks.
Sump Pump Repair or Replacement?
Some problems are simple repairs: a stuck float, a loose or unplugged cord, a tripped GFCI outlet, debris in the intake, or a failed check valve. A plumber will usually recommend replacing the pump when:
- The motor hums but does not pump, or has burned out.
- The pump is old and showing rust or noise.
- The pump cannot keep up with incoming water.
- The pit is too small and the float keeps catching.
Many homeowners replace the primary pump and add a backup at the same visit.
New Sump Pump Installation
In homes without a pump, installation may involve cutting the basement floor, digging a pit, installing a sealed basin, connecting it to drain tile if present, adding a dedicated electrical outlet (often by an electrician), and running a discharge line through the wall. That is a larger job than a pump swap, and may require a permit. A straight pump replacement in an existing pit is often done in a few hours.
Sump Pump Maintenance Checklist
- Pour a bucket of water into the pit and confirm the pump starts, empties the pit and shuts off.
- Check that the float rises and falls without catching on the pit wall or cords.
- Clear debris, gravel and silt from the pit and intake screen.
- Make sure the discharge outlet outside is clear and directs water away from the house.
- Test the battery backup and alarm, and check battery age.
- Listen for unusual noises and watch for constant running.
Do this before spring rains and after long dry stretches.
What Affects the Cost of Sump Pump Work
- Repair vs. replacement vs. new installation with a new pit
- Pump type, horsepower and quality
- Adding a battery backup, water-powered backup or alarm
- Check valve and discharge line changes
- Electrical work and permits
- Emergency or storm-time service
Sump pumps are part of our fixture services. Call (855) 902-0055 to connect with a local plumber.
How it works
- Call (855) 902-0055Tell us what is going on and your address. We answer 24/7.
- A local plumber comes outA plumber serving your area arrives, finds the problem and explains it.
- Fixed rightYou get the price before work starts, then the job is done and cleaned up.
Sump Pump Installation & Repair: common questions
How long does a sump pump last?
Many sump pumps last around seven to ten years, but lifespan depends on how often the pump runs, water quality and pump quality. Test it regularly and replace it before it fails during a storm.
Why is my sump pump running constantly?
Common causes are a stuck float switch, a failed check valve letting water flow back, an undersized pump, a high water table, or a pump that has lost capacity. A plumber can check each one.
Do I need a battery backup sump pump?
If your basement is finished, you store valuables there, or your area loses power during storms, a backup is strongly recommended. The primary pump cannot run without electricity.
Can a sump pump drain into the sewer line?
In many areas, no. Local codes often prohibit sump discharge into the sanitary sewer. Check with your city or a local plumber.
My basement flooded. Was it the sump pump?
It could be the pump, a power outage, a clogged discharge line or more water than the pump can handle. It could also be a sewer backup through a floor drain, which needs a different fix. A plumber can find the cause. See emergency plumbing.
How long does it take to replace a sump pump?
Replacing a pump in an existing pit often takes a few hours. Installing a new pit, adding a backup system or rerouting discharge takes longer.
Related
Sump Pump Installation & Repair near you
- Plumber in New York, NY
- Plumber in Los Angeles, CA
- Plumber in Chicago, IL
- Plumber in Brooklyn, NY
- Plumber in Houston, TX
- Plumber in Phoenix, AZ
- Plumber in Philadelphia, PA
- Plumber in San Antonio, TX
- Plumber in Bronx, NY
- Plumber in San Diego, CA
- Plumber in Dallas, TX
- Plumber in San Jose, CA
- Plumber in Austin, TX
- Plumber in Jacksonville, FL
- Plumber in Fort Worth, TX
- Plumber in Columbus, OH
- Plumber in Saint Louis, MO
- Plumber in Charlotte, NC
- Plumber in Indianapolis, IN
- Plumber in San Francisco, CA
- Plumber in Saint Paul, MN
- Plumber in Seattle, WA
- Plumber in Denver, CO
- Plumber in Oklahoma City, OK
Need a plumber?
Drains, leaks, water heaters, sewer lines and emergencies, day or night.
Call (855) 902-0055