Homeowner guide
What to Do When a Pipe Bursts: A Step-by-Step Emergency Guide
Short answer
When a pipe bursts, shut off the main water valve immediately, then cut power to wet areas if you can reach the breaker from a dry spot. Open faucets to drain the lines, turn off the water heater, photograph the damage, call your insurer and have a plumber repair the pipe.
The steps below walk through each of these in order, with what to avoid and how to prevent the next burst.
Step 1: Shut off the water
Every second counts. A burst supply line can release a large amount of water in minutes.
- Go straight to the main water shutoff valve. It is usually where the water line enters the house: basement front wall, crawl space, garage, utility room or outside on an exterior wall in warm climates.
- Turn a round handle clockwise until it stops, or turn a lever a quarter turn so it sits across the pipe.
- If the house valve fails or you cannot find it, use the curb stop at the water meter, usually in a box near the street. You may need a meter key.
- If the leak is at one fixture, closing its own valve may be enough.
See our full guide on how to find your main water shutoff valve.
Step 2: Stay safe around electricity and gas
- If water is near outlets, extension cords, appliances or the electrical panel, do not walk through it.
- If you can reach the breaker panel from a dry spot, turn off power to the affected area. If not, call an electrician or your utility.
- Watch for sagging ceilings. A bulging ceiling may be holding water and can collapse. Keep everyone out of the room.
- If a water heater or furnace is in the flooded area, keep away from it until it is checked.
- If you smell gas, leave the home and call your gas utility or 911 from outside.
Step 3: Drain the pipes and turn off the water heater
Even after the main is closed, water left in the pipes can keep leaking from the break.
- Open the cold faucets, starting on the lowest level, to drain the lines.
- Flush toilets once to empty the tanks if needed.
- Turn off the water heater. For a gas heater, set it to pilot or off; for an electric heater, turn off its breaker. A heater that runs with no water coming in can be damaged.
Step 4: Find the burst and limit the damage
Look for the source: a split pipe, a broken fitting, a failed supply hose or a cracked outdoor faucet. Common spots are unheated areas, exterior walls, under sinks, the attic and crawl spaces.
- Catch drips with buckets and lay towels to protect floors.
- Remove standing water with a mop or wet/dry vacuum.
- Move furniture, rugs, electronics and documents out of wet areas.
- Put aluminum foil or blocks under furniture legs that must stay.
- Open windows and run fans if it is safe and the power is on.
If the leak is in the ceiling, you can puncture a small hole at the lowest point of a bulge to drain it into a bucket, but only if it is safe to stand under it. If in doubt, stay out.
Step 5: Document the damage for insurance
Before cleanup goes too far, take clear photos and video of:
- The burst pipe or failed part
- Standing water and wet areas, wide and close-up
- Damaged flooring, walls, ceilings, cabinets and belongings
Keep receipts for anything you buy, such as fans, towels or a hotel stay. Keep damaged items if you can until the adjuster sees them. Call your insurance company promptly. Most policies require you to take reasonable steps to prevent further damage, which is what steps 1 through 4 do.
Step 6: Get the pipe repaired
Call a plumber to repair the break before you turn the water back on. A plumber will:
- Cut out the damaged section and replace it with new pipe and fittings
- Check for other weak or frozen sections, especially after a freeze
- Restore water slowly and test for leaks
- Suggest ways to prevent a repeat, such as insulation, rerouting or replacing old pipes
Step 7: Dry out the home
The EPA recommends drying water-damaged areas and items within 24 to 48 hours to help prevent mold growth. For a small, clean-water leak caught quickly, fans and a dehumidifier may be enough. For water inside walls, under floors, soaked into carpet pad or spread through several rooms, a professional water damage restoration company can measure moisture and dry the structure properly.
Why do pipes burst?
| Cause | What happens |
|---|---|
| Freezing | Water expands as it freezes, building pressure that splits the pipe. The leak often appears when it thaws. |
| Corrosion | Old galvanized steel and some copper pipes thin from the inside until they fail. See galvanized pipes. |
| Failing pipe material | Polybutylene pipe and fittings are known to fail. See polybutylene pipes. |
| High water pressure | Pressure above what the system is designed for stresses pipes and fittings. A failed pressure reducing valve is a common cause. |
| Water hammer | Sudden valve closures send shock waves through pipes and loosen joints. |
| Physical damage | Nails, screws, shifting soil or tree roots can crack pipes. |
To lower the risk in winter, read how to prevent frozen pipes.
What should I avoid after a pipe bursts?
- Do not turn the water back on to "see where it is leaking." Let a plumber pressure test the repaired line.
- Do not use electrical appliances or plug in fans while standing in water or on wet carpet.
- Do not use an open flame to thaw nearby pipes that may also be frozen.
- Do not throw away damaged items before documenting them for your insurer.
- Do not seal up wet walls or lay new flooring until the structure is confirmed dry with a moisture meter.
- Do not wait to call your insurer. Late reporting can complicate a claim.
If the burst happened during a freeze, assume other sections may also be frozen and check every faucet once water is restored.
Frequently asked questions
How fast should I shut off the water after a pipe bursts?
Immediately. Go to the main valve first, then deal with cleanup.
Can I fix a burst pipe myself?
A repair clamp or push-fit coupling can stop a small split temporarily, but a plumber should make the permanent repair and check the rest of the system.
Does homeowners insurance cover burst pipes?
Many policies cover sudden and accidental water damage from a burst pipe. Freezing in an unheated or vacant home and long-term leaks are commonly excluded. Read your policy and call your insurer.
Is it safe to stay in the house after a pipe bursts?
Usually, if the water is off, the electricity in wet areas is safe, ceilings are stable, and the water was clean. Leave if there is an electrical hazard, a sagging ceiling, sewage or a gas smell.
How do I know if a pipe burst inside a wall?
Signs include the sound of running water, wet or bulging drywall, stains, a sudden pressure drop and a moving water meter with fixtures off. See leak detection.
How long does a burst pipe repair take?
A simple repair in an accessible spot is often done in one visit. Pipes inside walls, ceilings or slabs take longer because they must be reached first.
Related services
Need a plumber?
Drains, leaks, water heaters, sewer lines and emergencies, day or night.
Call (855) 902-0055